换arduino IDE版本 去官网下载2.0.0版本的IDE 选对型号直接上传就行了 (1.8.5真不行
Programmed for Atmel STK-500 development board, detalis can be found at http://www.cs.hut.fi/Studies/T-106.5300/2007/stk500.html
STK8312重力IC, 驱动程序代码,读取重力感应的方向值,还有点击,敲打,自由落体等标志。
arduino nano 报错:avrdude: stk500_recv(): programmer is not responding(已解决) 文章目录arduino nano 报错:avrdude: stk500_recv(): programmer is not responding(已解决)前言:解决方案: 前言: 好久...
出现avrdude: stk500_recv(): programmer is not responding 最后发现明显板子信息没改对 到/usr/share/arduino/hardware/arduino/boards.txt 地址名字不定 !!! 主要是找到boards.txt的文件夹 打开它 然后看你...
如果你的IDE出现 avrdude: stk500_recv(): programmer is not responding 的提示的时候,注意看看你的板子数字0和数字1是不是插着东西。 如果你将数码管接到了数字0和数字1上,每次上传代码时,都要拔下来才行。因为...
https://www.htlinux.com/168/ avrdude: stk500_recv(): programmer is not responding In Debian squeeze and Ubuntu you may get an error like this while trying to upload your program…..To fix this
如果你的IDE出现avrdude: stk500_recv(): programmer is not responding的提示的时候,注意看看你的数字0和数字1是不是插着东西。 如果你将数码管接到了数字0和数字1上,每次上传代码时,都要拔下来才行。因为数据...
最近迷上了arduino,原因是无意间从同学那获取了一个arduino uno的单片机。...总是报avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x0
stk500_getsync() attempt 1 of 10: not in sync: resp=0x00 avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x00 avrdude: stk500_recv():...
ot responding 这个错误通常是由于与Arduino板连接的编程器无法响应而引起的。可能的原因包括: 1. 与Arduino板连接的USB电缆可能损坏或不良。 2. Arduino板上的芯片可能已经损坏或不良。 ...3. 与Arduino板连接的...
这个错误通常是因为Arduino与电脑连接不良或者串口设置有误导致的。以下是一些可能的解决方法: 1. 确认Arduino与电脑连接良好,尝试更换USB端口或者更换USB线。 2. 检查串口设置是否正确,比如波特率、数据位、...
这个错误通常是由于连接问题引起的。请检查您的连接,确保您的Arduino Nano与计算机正确连接,并且端口和波特率设置正确。您还可以尝试使用不同的USB端口或更换USB电缆。如果问题仍然存在,请尝试使用不同的编程器或...
这个错误提示通常是由于AVR芯片与编程器之间的通讯问题引起的。可能的原因是: 1. 编程器与计算机连接的USB接口不稳定。 2. 编程器与芯片之间的连接不良。 3. 芯片被损坏或者不支持使用的编程器。...
标签: 其他
avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xdc avrdude: stk500_recv(): programmer is not responding avrdude: stk500_getsync() ...
解决MEGA2560芯片avrdude: stk500v2_ReceiveMessage(): timeout问题
错误信息: avrdude:stk500_recv(): programmer is not responding avrdude:stk500_getsync() attempt 1of 10: not in sync: resp=0xlf
该楼层疑似违规已被系统折叠隐藏此楼查看此楼avrdude: stk500_recv(): programmer is not respondingavrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0xf6avrdude: stk500_recv(): programmer is not...
8. `os_ret = xTaskCreate((TaskFunction_t )m_recv_task, (const char* )g_my_uart_cfg[uart].m_recv_task_name, (uint16_t )g_my_uart_cfg[uart].m_recv_task_stk, (void* )&g_my_uart[uart], (UBaseType_t )g_my_...
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x1c avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0xe0 avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0xe0 ...
上传失败: 上传错误:exit status 1。
1. 飞马平台: ... 2. FAIMUI-CAR-V2的主芯片MCU: 芯片型号: LGT8F328P 芯片封装: LQFP48 ...芯片说明: 与ATmega328P兼容。...3. Mixly米思齐IDE向FAIMUI-CAR-V2烧录程序时,烧录失败,提示如下: ...
我最近下程序每次到最后都会提示下载失败‘Arduino:1.8.5 (Windows XP), 开发板:"Arduino/Genuino Uno"项目使用了 724 字节,占用了 (2%) 程序存储空间。最大为 32256 字节。全局变量使用了9字节,(0%)的动态内存,...
今天玩arduino数码管时上传报错:avrdude: stk500_recv(): programmer is not responding 原因: 我的TX和RX引脚即数字0,1接着数码管,而arduino上传进行数据交互时会用到这两个引脚 解决: 每次上传代码时...
用管理员身份运行
我的情况是,用了pc前置usb接口,这个接口本来用线接到主板上的,稳定性不佳,应该说是接触不良,信号稍弱。改换主板板载usb接口,解决。 当然如果rx, tx端口被占用也会出现这情况。只要烧写时将rx, tx端口卸载掉...